Chapter 4 - Preparation

This section specifies the correct methods and precautions for ensuring correct handling of the machine throughout the transportation process, as well as risks to be aware of.

4.1 Transport and store the machine

4.2 Site preparation

4.3 Commissioning the machine

 

4.1 Transport and store the machine

To prevent potential injuries and equipment damage before, during, and after installation, it is essential to follow the correct procedures for transporting SYIL 7 Series machines to their installation sites. 

4.1.1 General requirements and precautions

The machine is comprised of two main components: the machine body, and the control system. Ensure that all components and devices are properly installed on the machine’s body before transporting the fully-assembled machine to its intended position.

The machine should be moved either by crane or by forklift.

warning

  • Do not lift any other articles during transportation of the machine.

  • Do not go under the machine while it is being lifted.
  • Keep a safe distance from the machine and lifting equipment to avoid being struck during transportation.

caution-1

  • Before transporting the machine, check to ensure its components are correctly and securely installed.

  • Lift the machine slowly to ensure it remains completely balanced throughout the moving process.
  • Ensure the machine’s body, electrical control panel, and other electrical equipment are not subjected to strong vibrations during transportation.

  • The coolant compartment should be detached from the machine before transportation.
  • Ensure that the machine is positioned so that it will not hinder transportation in any way. If there is insufficient space for loading the machine on the transport mechanism, contact the person in charge of the worksite where it will be installed about adjusting the machine or other measures for ensuring transportation.

  • Once the machine is placed at the installation site and does not need to be moved further, ensure operating personnel are aware of any safety considerations arising from the installation process before they begin work.

To ensure safety, always use fixing devices to hold the machine’s spindles in place during transportation.

warning

  • Never operate the machine until you have completely dismounted the fixing devices for all components.

caution-1

  • Never use oil or other chemicals that may create a risk of fire.

4.1.2 Dimensions, mass, and center of gravity

Machine dimensions: 

1680mm x 1500mm x 2250mm

Shipping dimensions: 

definition: height, width, length, and weight configuration of the machine and auxiliary equipment as mounted to the skid. Shipping dimensions are measured with the machine on its shipping pallet.

2000mm x 1700mm x 2260mm(L*W*H)

 

Operating dimensions:

definition: width and length measurements that must be considered for maintenance and service of the machine, such as opening all enclosure and electrical power cabinet doors and location of auxiliary equipment.

2800mm x 2500mm x 2250mm 

 

Machine weight:

1500kg | 3306lbs

Shipping weight (in crate box): 

2040kg 

syil-x7-dimensions

syil-X7-layout-5

4.1.3 Lifting, handling, and transporting the product

The following safety rules must be absolutely followed when lifting and/or moving the
machine:
  • Use a forklift of sufficient capacity to raise or move the packed or machine.
  • Pay special attention to machine balance while lifting.
  • Have another person to help guide the way while lifting the machine.
  • Make sure the forks of the forklift protrude past the far edge of the machine base.
  • Do not raise the machine too high as this may cause a loss of stability.
  • The forklift should be driven by experienced personnel.

lifting-pull-ring-hole-1

lifting-pull-ring-hole-2

lifting-pull-ring-hole-3

4.1.4 Using fork-lifting truck

This machine should be lifted and moved by a forklift. Attention should be paid to the
machine balance during lifting and moving. This machine should be lifted under the following
conditions:

  • The loading capacity of the lifting equipment should be 5 tons at least.
  • Wire cables and chains of the lifting equipment should be able to bear a load of 5
    tons at least.
  • The packed machine is xx mm in width, xx mm in depth and xx mm in height.
    Ensure nobody is in the way and the path is not blocked before moving the packed
    machine. It could prevent the machine from collision.
  • Beware that the lifting truck might overturn because of an improper lifting height.
    This might cause people injury and damage the machine.
  • Always assign a person to guide the way to ensure safety.

When transporting the machine by forklift, be sure to take the following precautions:

  • Ensure you have read and understood the manual’s safety instructions before installing the machine.

  • Ensure the ground is free of lubricant oil, grease, or water to prevent slipping and falling during installation.

  • Before beginning installation, check and confirm that the machine has been placed in the correct position.

caution-1

  • Only personnel qualified to operate a forklift should attempt to transport the machine.

  • In order to avoid damaging the machine or its surroundings, a minimum of two people should be present while operating the forklift.
  • Lower the machine slowly to prevent impact with the ground.

  • A wooden pallet can be used to support the machine during the lifting process.

4.1.5 Sling crane or other lifting equipment

  • The loading capacity of the lifting equipment should be 5 tons at least. The loading
    capacity below 5 tons is prohibited.
  • This machine is xx mm in width, xx mm in depth and xx mm in height.
    Ensure nobody is in the way and the path is clear before commencing to move the
    machine. Otherwise collision with the machine might occur.
  • Pay special attention to machine balance while lifting.
  • Beware that the machine might be overturned because of an improper lifting height.
    Otherwise injury to people or machine damage may occur.
  • Always assign a person to guide the way to ensure safety.

When transporting the machine by crane, be sure to take the following precautions:

  • Position the base of the crane and the horizontal support plate so that the machine can be loaded with the fulcrum of the overhanging steel cable directly above its center.

  • Ensure the angle of the steel cable’s fulcrum does not exceed 90°. If possible, adjust the angle to 60°.

  • Ensure that the steel cable is secured on both sides of the pedestal or with a fixing device designed for transporting heavy equipment.

caution-1

  • Lift the machine slowly while ensuring it is balanced on all sides and that the lifting cables are taught against its external casing or outermost components.

  • If two or more people are lifting the machine, they should communicate to ensure they exert force on it simultaneously and in the same direction.
  • Do not use cables of inadequate length or that have sustained rust or other damage to lift the machine.

  • Lift the machine slowly. When one of the steel cables has reached maximum tension, temporarily halt lifting and check that the machine is balanced before continuing to lift it to the designated height.
  • The machine should be lowered slowly. When lowered almost to the ground, temporarily halt lowering and check that the machine’s base is level and aligned with the intended position, then resume lowering to set it down completely.

  • Lifting work should be performed only by experienced personnel.

      4.1.6 Storage with the machine packed

      • Ensure to fasten all the loose parts and have an anti-rust treatment of the machine.
      • Ensure to fix the machine firmly inside the crate to prevent the machine move from
        falling.
      • Ensure to enclose the machine with a waterproof cover to keep this machine from
        moisture or corrosive substance. It prevents the mechanical and electrical parts from
        damage.
      • Ensure to put an anti-moisture substance inside the crate.
      • Do not place the whole packing directly under the sunlight or near any other heat
        source.
      • Keep away from any corrosive substance or any equipment causing abnormal vibration.
      • The ambient temperature and moisture should be moderate and kept as constant and
        smooth as possible.

      4.1.7 Storage of the bare machine

      • Ensure to fasten all the loose parts and have an anti-rust treatment of the machine.
      • Ensure to fasten all the sliding guards and doors to prevent from moving even falling.
      • Ensure to enclose the machine with a waterproof cover to keep this machine from
        moisture or corrosive substance. Otherwise might cause the mechanical and electrical
        parts damage.
      • Ensure to put anti-moisture substance inside the electric cabinet, operating panel, and
        any other enclosure of this machine.
      • Do not place the machine directly under the sunlight or any other heat source. Keep
        away from any corrosive substance or any equipment causing abnormal vibration.
        The ambient temperature and moisture should be moderate and kept as constant and
        smooth as possible. Otherwise might cause the mechanical and electrical and
        electrical parts damage.
      • Ensure all the power supplies are off and the main power supply cables are taken off
        before put the pack in store.

      4.1.8 Securing the machine against shocks

      Counterbalance weight

      To prevent the counterbalance weight from swinging, loose the chain and put the
      counterbalance on the bracket to fasten the counterbalance weight.

      Headstock

      Move the working table to the middle and move the saddle to the main column as close as possible. Place a wooden block on top of the table, them lower the headstock slowly until it
      rests on the wooden block.

      Tool magazine

      Place wooden blocks under the tool magazine stand and tool magazine’s pivot to support
      the tool magazine.

      Operating panel

      Install a support plate under the panel’s pivot to support the operation panel.

      Power cabinet

      Place wooden blocks under the power cabinet to support the power cabinet.

      Others

      Ensure to fasten all the loose parts firmly inside the crate.

      4.1.9 Moving the machine into final position

      Machine on shipping pallet with auxiliary equipment may be moved near the final position before it is removed from shipping pallet.

      Remove the packing of machine.

      remove-from-pallet-1-1

      Take off the coolant tank from the pallet

      remove-from-pallet-2-1remove-from-pallet-3-1

      Remove the nut from the screw

      remove-from-pallet-4-1

      remove-from-pallet-5-1

      Raise the machine from pallet

      remove-from-pallet-6-1

      remove-from-pallet-7-1

      Keep the machine with forklift, and move the pallet away

      remove-from-pallet-8-1

      Put the machine on the ground, and adjust level of machine

      When machine local on ok, the next is wiring, this is the power input terminal and gas source interface.

      remove-from-pallet-9-1 remove-from-pallet-10-1

      Add rail oil (#20~#70)and cutting fluid(the tank max is 80L, in normal, 70L is enough)

      remove-from-pallet-11-1

      Remember remove all support of X axis, Y axis, Z axis and ATC

      remove-from-pallet-12-1

      remove-from-pallet-14-1

      remove-from-pallet-13-1

      4.1.10 Inspect the machine for damage

      SYIL recommends that the machine equipment be inspected for shipping damage before unloading and placing machine onto foundation.

      • Remove all wrapping around machine
      • Examine the machine for structural damage.
      • Note any shipping damage to the machine on the shipper’s bill of lading. It is the customer’s responsibility to file a damage claim.
      • Photograph any equipment damage for your records.

      Moving the machine into final position

      SYIL recommends that the customer review this section to determine if there is proper capacity and ability to lift and place the machine into the location. If not, then a rigging agency should be contacted.

      4.1.11 Leveling 

      Following transportation, precise horizontal leveling and careful installation of the SYIL 7 Series machine's electrical components is needed ensure its long-term performance and safe operation.

      Perform horizontal leveling in the following sequence using a spirit level with a unit scale sensitivity of 0.02mm/m:

      1. Place the horizontal adjustment seat on the installation position at the bottom. The machine should be installed so as to facilitate adjustment of the positioning bolts used to level the machine.

      2. Place the spirit level on the worktable and collect measurements.
      3. Adjust the machine using the positioning bolts until leveled within 0.04mm/m in the front-to-back direction.

      4. Adjust the machine using the positioning bolts until leveled within 0.04mm/m in the front-to-back direction.

      caution-1

      • Keep the level gauges’ contact surfaces clean and prevent any dirt or dust from entering the measurement area.

      • Tilting or abrasion of the machine’s body during transport can cause horizontal leveling imbalances that will impact its control system, resulting in equipment faults.

      • When the level gauge is moving, make sure it is not obstructed by the chuck or tailstock.

      • Ensure the machine’s anchor bolts and nuts are firmly installed and use them to make final horizontal leveling adjustments.
      • Following initial leveling during installation, perform routine leveling at the intervals specified in the following table:

      Leveling
      Stage of Service Life Frequency
      Two to three days after installation of the machine Daily
      Within 6 months of installation Monthly
      After six months have passed since installation Quarterly

       

      4.2 Site preparation

      4.2.1 Minimum space needed

      A distance of at least 500 mm is required from machine to wall end objects or between machines to ensure easy repair, cleaning, and maintenance of machine. 

      The area must meet the following space requirements.

       

      This takes into account to:

      • Allow more space to access the rear of the machine for maintenance and repairs.
      • Allow additional space around the machine for servicing and safe operation. Leave room
        for removing the coolant tank and the chip box.

      4.2.2 Installation site requirements

      Selecting a suitable installation site is essential to ensuring the performance and safety of SYIL 7 Series machines.

      This section specifies general and environmental requirements for machine installation sites.

      warning

      • Before installing the machine, ensure you have full read and understand the safety instructions in this manual.

      • Ensure the ground is free of lubricant oil, grease, or water to prevent slipping and falling during installation.

      • Ensure that the machine has been correctly installed before operating it for the first time.

      General Conditions

      The following environments are suitable machine installation sites:

      • Environments free of condensation or dew brought by daily temperature changes.

      • Environments with flat, slip-resistant surfaces.

      • Well-supplied, well-maintained public facilities.

      • Environments with sufficient space for adjustment or repositioning of the machine.

      • Environments without fire or explosion hazards.

      The following installation environments are not suitable machine installation sites:

      • Environments with direct sunlight, proximity to a heat source, or with heavy temperature fluctuations.

      • Environments with high levels of dust or humidity.

      • Environments located near vibrating machinery.

      • Environments built on soft foundations.

      • Environments with slanted or slippery flooring.

      caution-1

      • Vibration dampeners should be installed around the machine if sources of vibration are present in or around the worksite.

        If any special components have been selected for installation on the machine, ensure there is enough space for maintenance.

      Environmental Requirements

      The following table specifies detailed environmental requirements for machine installation sites:

       
      Environmental Factors Requirements
      Temperature Between 0°C and 4°C
      Relative Humidity Between 10% and 75%
      Clearance Space No less than 600mm at all points on the machine to ensure repair and maintenance access
      Lighting No dimmer than 300 lux
      Air Quality No higher than AQI 100
      Noise No higher than 70db
      Storage Temperature Between -20°C and 65°C

      caution-1

      • An air source equipped with a dehumidifier should be installed at the worksite to prevent excess humidity from damaging the machine.

      To ensure the operational efficiency and accuracy of this machine, a proper foundation is
      required.

      It is recommended that this machine should be located in a plant with an ambient
      temperature of around 20°C, and without the influence of dampness, chemical gas
      , or vibration. This machine should be installed under the following conditions:

      • Do not install the machine in a location near vibration sources, such as air compressor,
        punch press, etc. Otherwise, poor machining accuracy may result.
      • Do not expose this machine and its NC controller to direct sunlight, moisture, etc.
      • Keep this machine away from dust, corrosive substances, etc.

      This machine should be installed under the correct environment as following:

      • Supply voltage:90% to 110% of the rated voltage.
      • Source frequency:Rated frequency ±1 Hz.
      • Ambient temperature: 5°C to 40°C.
      • Altitude: shall be at altitudes up to 1000m above mean sea level.
      • Relative humidity – less than 90%, and not exceed 50% at 40°C.
      • Atmosphere: Free from excessive dust, acid fumes, corrosive gases and salt.
      • Do not expose the machine directly under sunlight or heat source, which might result in
        considerable environmental temperature changes.
      • Do not place the machine near any abnormal vibrations.
      • Do not place this machine near to magnetic and static electric fields.
      • Do not place this machine near to air compressors or presses.
      • Do not place this machine near any equipment causing electronic noise.
      • Electrical equipment shall withstand the effects of transportation and storage temperature
        within a range of -25°C to 55°C and for short periods not exceeding 24 hours at up to
        +70°C.

        4.2.3 Foundation requirements

        Ensure the foundation and floor are capable of supporting the machine’s weight.
        The foundation must be able to support the weight of the machine and should be
        constructed of continuous concrete (reinforced is best). The thickness and consistency of
        the concrete must be compatible with industry standards for supporting machine weight.
        Actual requirements will depend upon the physical properties of underlying soil. A local
        civil engineer must be consulted if soil conditions are questionable.

        All SYIL machining centers sit on leveling pads that allow the machine to be leveled.

        The following guidelines are to be taken into account:

        • Flatness allowance of the floor level should be within +10 mm (0.39 in).
        • Take precautions so that there are no cracks in the concrete.
        • Leveling bolts are supplied in the shipping box with the machine.
        • Based on the soil conditions, the stiffness of the foundation shall be determined, so that the machine base does not deflect more than 0.013 mm (0.0005) inches to maintain the machine accuracy and performance.
        • Local masonry contractor and/or civil engineers must be consulted for additional recommendations (e.g. depth, reinforcing steel based on the load bearing characteristics of the soil) to achieve specified performance of the machine.
        • Foundation contractor must paint foundation with a liquid proof paint prior to the installation of the machine to prevent the foundation from absorbing moisture.

        For improved performance, accuracy, and reliability, SYIL recommends that the X7 machines is
        anchored to the foundation. If a machine is to be anchored, failure to follow the recommended foundation guidelines may void guarantees of quoted machine accuracy. If a machine is to be anchored, the following requirements must be met:

        • Core drilled hole must be prepared to ensure proper adhesion of grout to the foundation concrete.
        • The grout and anchor bolt manufacturers’ recommendations must be followed to ensure full strength of the foundation.
        • After proper cure time, the anchor bolt must be capable of allowing a minimum torque transmission of 271 Nm (200 ft-lb).


        4.2.4 Electrical service requirements

        The customer is responsible for providing incoming electrical power to the SYIL X7 machine.

        Ensure there is appropriate power availability and the voltage requirements are met.

        The machine’s full load KVA power rating can be found on the serial number identification tag that is affixed to the electrical power cabinet.

        A certified electrician should ensure the following electrical service requirements:

        • On-site wiring must comply with all applicable electrical codes.
        • Dedicated, grounded 3-phase AC power is required to prevent high/low voltages, spikes, surges, and noise.
        •  The AC power source shall be balanced and must match the voltage specifications on the machine electrical cabinet.
        • Wiring to the machine must be capable of supplying continuous specified amperage.
        • Failure to provide the required power parameters may affect safety, machine performance, and the warranty.

        Ensure transformer requirements are met.

        If a transformer is required and the machine was not equipped with one, the customer is responsible for providing a transformer. The transformer must meet SYIL machine operating voltage requirements. It is the customer’s responsibility to have a qualified electrician connect the transformer to the power source.

        Ensure proper grounding of machine.

        The electrical and electronic control systems of the machining center are interconnected internally and terminate at a single point ground (SPG) terminal. The SPG provides only one conducting path between the machine and external ground, preventing an unwanted ground loop (ground differential voltage). The SPG is located inside the machine power cabinet.

        The SPG must be properly connected to the ground circuit of the AC power source. The grounding conductor must be sized to conform to all applicable electrical codes. However, SYIL recommends that the size of the neutral conductor (when applicable) be at least the size of the phase (current carrying) conductors.

        4.2.5 Compressed air requirements

        Ensure compressed air is available.

        A continuous supply of clean and dry compressed air is required for proper machine operation. Compressed air will connect to the machine’s filter, regulator, lubricator (FRL) unit. Use these specifications:

        • Air humidity dew point: 2º C (35º F).
        • Use a minimum 13 mm (0.5 in) diameter (trade size) pipe supply line to the machine.
        • Install a drip leg in the line before the connection to the FRL unit. The drip leg will help remove the moisture in the air supply and improve operation of the FRL unit.
        • Do not use quick-coupler type fittings at the connection to the FRL unit or in the supply line to the machine because these fittings restrict the air supply.

        4.2.6 Recommended operating temperature

        Ensure operating temperature requirements are met.

        SYIL machines may be operated in a facility with ambient temperatures ranging from 0º C to 35º C (32º F to 95º F) and in non-condensing relative humidity up to 95%. The electrical cabinet has a heat exchanger to regulate the temperature inside the cabinet to ensure that the electronics operate within their temperature limits. Some high-duty cycle applications may require that the heat exchanger be replaced with an optional air conditioner.

        Set up the machine away from external heat sources, such as direct sunlight and heating vents.

         

        4.3 Commissioning the machine

         

        SYIL Machine Inspection List

        Model:

         

        Serial:

         

        Casting: 

         

        Cabinet:   

         

        Country:

         

        Customer:

         

        Date:    

         

         
        Machine Configuration

        System:

         

        Voltage:  

         

        Spindle:  

        RPM

        SP motor

         

        XYZ motor:

         

        ATC:        

         

        4/5th:    

         

        Tool setter:    

         

        Probe:      

         

        TF:

         

         
        Machine Accuracy
          
         

        NO

        Picture

        Inspection items and methods

        Result

        J1

        Vertical and horizontal level bubbles must be in the middle

        Check:

        J2

        Parallelism of worktable

        Requirements:

        X: 0.02mm/300mm

        Y: 0.02mm/300mm

        X:

         

        Check:

        Y:

         

        Check:

        J3

        Parallelism between X-axis and T-slot

        Requirements: 0.02mm/300mm

        Check:

        J4

        Measuring the verticality of X-Y plane

        X-Y plane: Measuring the Y direction based on the x direction

        Requirements: 0.02mm/200mm

        Check:

        J5

        Measuring the verticality of column:

        X-Z plane: Measuring the z direction based on the x direction

        Y-Z plane: Measuring the z direction based on the y direction

        Requirements:

        X-Z: 0.02mm/200mm

        Y-Z: 0.02mm/200mm

        X-Z:

         

         

        Check:

         

         

         

        Y-Z:

         

         

        Check:

        J6

        Measuring the verticality of head:

        X-Z plane: Measuring the z direction based on the x direction

        Y-Z plane: Measuring the z direction based on the y direction

        Requirements:

        X-Z: 0.02mm/200mm

        Y-Z: 0.02mm/200mm

        X-Z:

         

         

        Check:

         

         

         

        Y-Z:

         

         

        Check:

        J7

        Spindle tram

        Requirements: 0.02mm/200mm

         

        Check:

        J8

        Spindle play:

        Requirements:

        Near spindle nose:0.01mm

        Leave spindle 100mm:0.02mm

        100mm:

         

        Check:

         

         

        Electrical Equipment

         

        System model

         

        System serial:

        Servo

        Spindle

        servo motor:

        2.2kw□ 3.7kw□

        spindle driver:

        台达□ 蒙德□ LNC□ SMD□

        driver serial:

        Electric spindle

        high speed spindle

        1.5kw□ 2.2kw□ 6kw□

        motor serial:

        driver special:

        LNC□ INVT□ SMD□

        driver serial

        Frequency conversion

        Spindle

        VF motor

        1.1kw□ 1.5kw□

        变频器:

        INVT□

        VFD serial:

        X-axis

        step driver:

        研控□ 纳川□

        motor special:

        57□ 86□ 110□

        servo driver:

        V70□ LNC□ SMD□

        driver serial:

        motor special:

        0.75kw□   1kw□ 2.2kw□

        motor serial:

        Y-axis

        None □

        step driver:

        研控□ 纳川□

        motor special:

        57□ 86□   110□

        servo driver:

        V70□ LNC□ SMD□

        driver serial:

        motor special:

        0.75kw□ 1kw□   2.2kw□

        motor serial:

        Z-axis

        step driver:

        研控□ 纳川□

        motor special:

        57□ 86□   110□ 带抱闸□

        servo driver:

        V70□ LNC□ SMD□

        driver serial:

        motor special:

        0.75kw□ 1kw□   2.2kw□ 带抱闸□

        motor serial:

        4 axis

        None □

        step driver:

        研控□ 纳川□

        motor special:

        57□ 86□   110□

        servo driver:

        V70□ LNC□ SMD□

        driver serial:

        motor special:

        0.75kw□ 1kw□   2.2kw□

        motor serial:

        5 axis

        None □

        servo driver:

        V70□ LNC□ SMD□

        driver serial:

        motor special:

        0.75kw□ 1kw□   2.2kw□

        motor serial:

         

        Function Testing

        NO

        Testing items

        Result

        Remark

        J1

        drawbar ok

         

         

        tool change blow ok

         

         

        clamp/unclamp signal ok

         

         

        J2

        0.6 Mpa/ air pressure 0.6mpa

         

        None□

        J3

        lube work 10s and delay 3h

         

         

        J4

        Oil discharge work ok

         

         

        J5

        MPG ok

         

        None□

        J6

        Coolant motor direction ok

         

        None□

        J7

        X limit ok

         

         

        Y limit ok

         

         

        Z limit ok

         

         

        J8

        X backlash

        mm

         

        Y backlash

           mm

         

        Z backlash

           mm

         

        J9

        Spindle test

        Spindle direction ok

         

         

        100rpm 3min

         

         

        500rpm 3min

         

         

        1000rpm 10min

         

         

        2000rpm 10min

         

         

        4000rpm 10min

         

         

        6000rpm 10min

         

         

        8000rpm 10min

         

         

        10000rpm 3min

         

         

        12000rpm 3min

         

        None□

        J10

        Tapping

        None □

        direction ok

         

         

        deviation

         

         

        J11

        Testing

        None □

        0.3mpa/ alarm pressure 0.3mpa

         

         

        Spindle position ok

         

         

        ATC home ok

         

        None□

        tool change in TSM ok

         

        None□

        tool change in MDI ok

         

         

        run 8h without tool

         

         

        run 8h with tool

         

         

        J12

        Comb sheet

        metal inspection

        None □

        door moving ok

         

         

        table protect ok

         

         

        side windows open ok

         

         

        junction no leaking

         

         

        wash gun ok

         

        None□

        leaking test for 20min

         

         

        J13

        4 axis test

        None □

        4th brake signal ok

         

        None□

        G0跑动4小时无报警/run rapid move for 4h

         

         

        J14

        Tool setting

        instrument test

        None □

        ATM screen work ok

         

         

        tool length calibrate ok

         

         

        tool length measure ok

         

         

        tool radius calibrate ok

         

        None□

        tool radius measure ok

         

        None□

        tool broken measure ok

         

         

        J15

        Probe test

        None □

        probe radius calibrate

         

         

        probe length calibrate ok

         

         

        hole center measure ok

         

         

        cylinder center measure ok

         

         

        groove center measure ok

         

         

        boss center measure ok

         

         

        X surface measure ok

         

         

        Y surface measure ok

         

         

        Z surface measure ok

         

         

        outer corner measure ok

         

         

        inner corner measure ok

         

         

        J16

        Delivery inspection

        spindle have been support

         

         

        tool magazine have been fixed

         

         

        front door have been fixed

         

         

        machine is antirust

         

         

        J17

        Insulation resistance measured

        >500MΩ,Insulation resistance>500 MΩ